50videosJoe Pie
184K subscribers on YouTube
Shorts, livestreams, trailers and promos are never listed. Unless a curator approved this channel in full, only individually picked videos appear.
Playlists · 10
16:56Captured Screws in Holes and Slots - 4 Different Styles
24.2K views
Four ways to make captured screws in holes and slots.
38:55Creative Ways to Hold and Machine Small Parts
39K views
Fixturing techniques for holding small, awkward parts on a mill and lathe.
20:03Eccentric Turning and Soft Emergency Collets
27.3K views
How to turn eccentric features and make soft emergency collets.
16:22Machining both sides of a Part ? How do you hold it ?
24.4K views
Workholding for machining both sides of a part.
13:16Make Your Own Angle Blocks - DIY - Super Accurate
24.8K views
Making accurate angle blocks for setups.
32:11Manually Turning Tapers and Decorative Features on My 50 cal. Cannon Barrel
20.4K views
Turning tapers and decorative features by hand on the lathe.
27:161 Day Build --- Make Your Own Drill Press Vise
45.4K views
A 27-minute video from Joe Pieczynski: “1 Day Build --- Make Your Own Drill Press Vise”.
9:561 person - Honda CB750F Engine Removal
A 10-minute video from Joe Pieczynski: “1 person - Honda CB750F Engine Removal”.
10:251/12 Scale Miniature Wood Lathe - Video # 1
12K views
A 10-minute video from Joe Pieczynski: “1/12 Scale Miniature Wood Lathe - Video # 1”.
21:511/12 Scale Miniature Wood Lathe - Video # 2 - The Bed
11.1K views
A 22-minute video from Joe Pieczynski: “1/12 Scale Miniature Wood Lathe - Video # 2 - The Bed”.
24:03A Great Fixture Technique to Simplify Possibly Difficult Features
48.5K views
A 24-minute video from Joe Pieczynski: “A Great Fixture Technique to Simplify Possibly Difficult Features”.
10:31A Great Trick for Machining Features on Angled Surfaces
22.8K views
A 11-minute video from Joe Pieczynski: “A Great Trick for Machining Features on Angled Surfaces”.
20:10A Miniature Shaper from the 1800's -- Making The Table and Apron
32.9K views
A 20-minute video from Joe Pieczynski: “A Miniature Shaper from the 1800's -- Making The Table and Apron”.
12:23A Quick and Simple Method for Making a T Slot Cutter.
86.4K views
A 12-minute video from Joe Pieczynski: “A Quick and Simple Method for Making a T Slot Cutter.”.
12:38A Simple Chuck Modification to Improve Parallelism of Your Parts
524K views
A 13-minute video from Joe Pieczynski: “A Simple Chuck Modification to Improve Parallelism of Your Parts”.
12:30A close-up look at the 13" Clausing Lathe
47.9K views
A 12-minute video from Joe Pieczynski: “A close-up look at the 13" Clausing Lathe”.
40:42Are All Taps The Same -- Part 2
41.9K views
A 41-minute video from Joe Pieczynski: “Are All Taps The Same -- Part 2”.
22:03
11:14Backlash and Part Geometry
17.5K views
A 11-minute video from Joe Pieczynski: “Backlash and Part Geometry”.
35:25Bad Turned Surface Finish and Some Reasons Why
89.7K views
A 35-minute video from Joe Pieczynski: “Bad Turned Surface Finish and Some Reasons Why”.
32:52Basics of a Parting Tool
214K views
A 33-minute video from Joe Pieczynski: “Basics of a Parting Tool”.
17:03Better Edge Cut Control on Your Bandsaw
38.7K views
A 17-minute video from Joe Pieczynski: “Better Edge Cut Control on Your Bandsaw”.
20:08Bolt Circle, Layout and Construction Basics
58.2K views
A 20-minute video from Joe Pieczynski: “Bolt Circle, Layout and Construction Basics”.
16:57Boring Soft Jaws Using a Jaw Spider
53.4K views
A 17-minute video from Joe Pieczynski: “Boring Soft Jaws Using a Jaw Spider”.
9:58CNC Engraving of a complex graphic
4.58K views
A 10-minute video from Joe Pieczynski: “CNC Engraving of a complex graphic”.
14:09CNC Machining Center Part 1
23.7K views
A 14-minute video from Joe Pieczynski: “CNC Machining Center Part 1”.
13:09CNC Machining Center Part 2
13.2K views
A 13-minute video from Joe Pieczynski: “CNC Machining Center Part 2”.
14:35CNC Machining Center Part 3
15.6K views
A 15-minute video from Joe Pieczynski: “CNC Machining Center Part 3”.
24:00CNC Machining Center Part 4
11.4K views
A 24-minute video from Joe Pieczynski: “CNC Machining Center Part 4”.
14:21CNC Machining Center Part 6
6.7K views
A 14-minute video from Joe Pieczynski: “CNC Machining Center Part 6”.
8:51CNC Machining Center Part 7
7.75K views
A 9-minute video from Joe Pieczynski: “CNC Machining Center Part 7”.
10:55CNC Machining Center Part 5
9.58K views
A 11-minute video from Joe Pieczynski: “CNC Machining Center Part 5”.
7:06CNC Surface Milling -- Trial and Error
19.8K views
A 7-minute video from Joe Pieczynski: “CNC Surface Milling -- Trial and Error”.
7:16Can You Use a Hole Saw To Enlarge an Existing Hole?....YES
15.8K views
A 7-minute video from Joe Pieczynski: “Can You Use a Hole Saw To Enlarge an Existing Hole?....YES”.
41:53Chasing and Repairing Damaged Threads
113K views
A 42-minute video from Joe Pieczynski: “Chasing and Repairing Damaged Threads”.
10:53Clamping Thin and Irregularly shaped parts in the mill
113K views
A 11-minute video from Joe Pieczynski: “Clamping Thin and Irregularly shaped parts in the mill”.