33videosADES WORKSHOP
15.2K subscribers on YouTube
Shorts, livestreams, trailers and promos are never listed. Unless a curator approved this channel in full, only individually picked videos appear.
Playlists · 8
32:13A Tooling plate for my mill Part2
Second part of a tooling plate build for a mill, showing further machining work.
58:32A quick change tool post DTI holder for the mini lathe
Builds a quick-change tool post DTI holder for the mini lathe, showing design and fabrication steps.
44:30A tooling plate for my mill part 1
Starts a tooling plate project for a new mill.
31:44Accurately setting an angle on the compound slide
Demonstrates accurately setting an angle on a lathe compound slide, a precise machining technique.
28:18Adjustable milling workpiece stop completed
Shows completion of an adjustable milling workpiece stop, a practical shop-made tool.
28:17Chain saw clutch removal tool
Shows making a tool to remove a chain saw clutch, a practical fabrication task.
46:23Clock Tales Part 1.
Opens a clock-building series.
42:42Clock Tales part 3
Third installment of the clock build, demonstrating machining and assembly of clock components.
43:08Clock tales part 2 Beating about the bush
Continues the clock-building project, working through a tricky stage of fabrication.
1:05:41Clock tales part 4
Continues the clock build series, showing machining steps for clock parts.
48:47Clock tales part 5
Part of a clock-building series.
21:15Clocking square stock in a 4 jaw Chuck
Demonstrates clocking square stock in a four-jaw chuck, a core lathe setup skill.
26:28Compound Slide Replacement Block part 3
Third part of making a compound slide replacement block, showing finishing machining work.
26:03Compound slide replacement block part 2
Second part of building a compound slide replacement block, detailing further machining steps.
27:25Compound slide replacement block part1
Begins making a compound slide replacement block for a lathe.
38:24Custom made Darts part 1
Begins machining custom darts from raw stock, explaining design and turning steps.
17:08Custom made darts part 2, completed.
Completes a custom darts project, showing final machining and assembly steps.
23:29Cutting My DRO scale . X axis fitting to the Warco WM16B part 1
Shows cutting and fitting a DRO scale to the X axis of a Warco WM16B mill.
10:28Finished the box for the SG low profile DTI holder
Finishes a storage box for a low-profile DTI holder, showing fabrication and fitting work.
24:59Finishing off the DRO installation on my Warco WM16B mill .The Y axis.
Covers finishing the Y axis DRO installation on a Warco WM16B mill, showing fitting and calibration steps.
29:46Fire piston part 2
Second part of the fire piston project, demonstrating further lathe work and assembly.
28:20Fire piston part 3
Continues the fire piston build, showing precision turning and fitting steps.
35:59First cuts . Aligning the bed and setting the tailstock alignment. Mini late part 28
Covers aligning the lathe bed and setting tailstock alignment during a mini lathe rebuild.
22:59Fitting an electrical interlock to my spindle lock for safety reasons
Walks through fitting an electrical interlock to a lathe spindle lock for operator safety.
17:49Fitting my X axis DRO part 2
Continues fitting an X axis DRO scale to a mill, part two of a practical installation guide.
33:45Installing a Three Axis DRO on My WM16B mill . the Z Axis.
Details installing the Z axis of a three-axis DRO system on a mill.
40:54Jacqui's Vape stand part 1
Begins building a vape stand.
31:48Jacqui's Vape stand part2
Second part of making a vape stand.
20:53Machining a large part on a small mill
Demonstrates machining a large part on a small milling machine, addressing setup and workholding challenges.
15:51Machining an ER32 collet chuck to fit my Warco Lathe part 2
Continues machining the ER32 collet chuck project, demonstrating turning and boring steps.
24:09Machining an ER32 collet chuck to fit my Warco lathe part3
Finishes machining an ER32 collet chuck to fit the Warco lathe, showing final fitting steps.
43:47Making Stefan Goteswinters low profile DTI holder . My way .
Builds a low-profile DTI holder based on Stefan Gotteswinter's design, adapted to the maker's own approach.
34:38Making a Brass Knocker tool for the workshop
Shows making a brass knocker tool for the workshop, a specific machining project.
54:42Making a Flycutter for a fellow engineer and some more Arbour press improvements.
Builds a flycutter for another engineer and improves an arbour press, showing tool design and machining.
33:53Making a ball turning tool
Begins making a ball turning tool.
29:14Making a ball turning tool part 2 . 100th upload.
Second part of making a ball turning tool, marking the channel's 100th upload.