47:362014W ENGR380 Lecture18 Spur Gear Design (Lewis Equation for Tooth Bending Stress), Part I
Intermediate
A 48-minute video from Yang Cao: “2014W ENGR380 Lecture18 Spur Gear Design (Lewis Equation for Tooth Bending Stress), Part I”.
Yang Cao
13K subscribers on YouTube
Shorts, livestreams, trailers and promos are never listed. Unless a curator approved this channel in full, only individually picked videos appear.
47:36
46:512014W ENGR380 Lecture19 Spur Gear Design, Part II
Intermediate
A 47-minute video from Yang Cao: “2014W ENGR380 Lecture19 Spur Gear Design, Part II”.
46:242014W ENGR380 Lecture20 Gear Design using AGMA Equation, Part I
Intermediate
A 46-minute video from Yang Cao: “2014W ENGR380 Lecture20 Gear Design using AGMA Equation, Part I”.
51:292014W ENGR380 Lecture21 Gear Design using AGMA Equation, Part II
Intermediate
A 51-minute video from Yang Cao: “2014W ENGR380 Lecture21 Gear Design using AGMA Equation, Part II”.
49:142014W ENGR380 Lecture22 Effect of Terms in AGMA Equations
Intermediate
A 49-minute video from Yang Cao: “2014W ENGR380 Lecture22 Effect of Terms in AGMA Equations”.
47:492014W ENGR380 Lecture23 General Shaft Design Considerations
Intermediate
A 48-minute video from Yang Cao: “2014W ENGR380 Lecture23 General Shaft Design Considerations”.
51:172014W ENGR380 Lecture24 Shaft Design, An Example
Intermediate
A 51-minute video from Yang Cao: “2014W ENGR380 Lecture24 Shaft Design, An Example”.
48:432014W ENGR380 Lecture25 Key Design
Intermediate
A 49-minute video from Yang Cao: “2014W ENGR380 Lecture25 Key Design”.
46:392014W ENGR380 Lecture26 Introduction to Bearings
Intermediate
A 47-minute video from Yang Cao: “2014W ENGR380 Lecture26 Introduction to Bearings”.
49:172014W ENGR380 Lecture27 Selection Procedures of Bearings
Intermediate
A 49-minute video from Yang Cao: “2014W ENGR380 Lecture27 Selection Procedures of Bearings”.
50:222014W ENGR380 Lecture28 Variable Loading of Bearings and Introduction to Screws
Intermediate
A 50-minute video from Yang Cao: “2014W ENGR380 Lecture28 Variable Loading of Bearings and Introduction to Screws”.
50:062014W ENGR380 Lecture30 Threaded Fasteners and Stiffness of Bolted Joints
Intermediate
A 50-minute video from Yang Cao: “2014W ENGR380 Lecture30 Threaded Fasteners and Stiffness of Bolted Joints”.
52:582014W ENGR380 Lecture31 Tension Joint Safety Analysis, Part 1
Intermediate
A 53-minute video from Yang Cao: “2014W ENGR380 Lecture31 Tension Joint Safety Analysis, Part 1”.
51:042014W ENGR380 Lecture32 Tension Joint Safety Analysis, Part 2 and Introduction to Welded Joint
Intermediate
A 51-minute video from Yang Cao: “2014W ENGR380 Lecture32 Tension Joint Safety Analysis, Part 2 and Introduction to Welded Joint”.
49:002014W ENGR380 Lecture33 Design for Welded Joints, Part 1
Intermediate
A 49-minute video from Yang Cao: “2014W ENGR380 Lecture33 Design for Welded Joints, Part 1”.
50:552014W ENGR380 Lecture34 Design of Welded Joints, Part 2
Intermediate
A 51-minute video from Yang Cao: “2014W ENGR380 Lecture34 Design of Welded Joints, Part 2”.
40:042014W ENGR380 Lecture35 Mechancial Springs
Intermediate
A 40-minute video from Yang Cao: “2014W ENGR380 Lecture35 Mechancial Springs”.
1:17:422014W ENGR487 Lecture11 Pole Placement
A 78-minute video from Yang Cao: “2014W ENGR487 Lecture11 Pole Placement”.
1:19:142014W ENGR487 Lecture12 Pole Placement for Reference Tracking, Deadbeat Control
A 79-minute video from Yang Cao: “2014W ENGR487 Lecture12 Pole Placement for Reference Tracking, Deadbeat Control”.
1:11:392014W ENGR487 Lecture13 Mapping from s-plane to z-plane, Part I
A 72-minute video from Yang Cao: “2014W ENGR487 Lecture13 Mapping from s-plane to z-plane, Part I”.
1:20:372014W ENGR487 Lecture14 Mapping fromms-plane to z-plane, Part II
A 81-minute video from Yang Cao: “2014W ENGR487 Lecture14 Mapping fromms-plane to z-plane, Part II”.
1:12:112014W ENGR487 Lecture15 Full-order Observer Design
A 72-minute video from Yang Cao: “2014W ENGR487 Lecture15 Full-order Observer Design”.
1:17:542014W ENGR487 Lecture16 Reduced-order Observer Design
A 78-minute video from Yang Cao: “2014W ENGR487 Lecture16 Reduced-order Observer Design”.
1:15:472014W ENGR487 Lecture17 Min/Max and Lagrange Multiplier
Intermediate
A 76-minute video from Yang Cao: “2014W ENGR487 Lecture17 Min/Max and Lagrange Multiplier”.
1:16:012014W ENGR487 Lecture19 Linear Optimal Control, Part 2 and Review on Probability and Statistics
Intermediate
A 76-minute video from Yang Cao: “2014W ENGR487 Lecture19 Linear Optimal Control, Part 2 and Review on Probability and Statistics”.
1:18:042014W ENGR487 Lecture20 Review of Probability and Statistics Concepts and Kalman Filter
Intermediate
A 78-minute video from Yang Cao: “2014W ENGR487 Lecture20 Review of Probability and Statistics Concepts and Kalman Filter”.
1:10:162014W ENGR487 Lecture21 Kalman Filter
Intermediate
A 70-minute video from Yang Cao: “2014W ENGR487 Lecture21 Kalman Filter”.
1:20:312017W APSC248 Lecture15 Double Integral, Part 2
Intermediate
A 81-minute video from Yang Cao: “2017W APSC248 Lecture15 Double Integral, Part 2”.
37:46Tutorial on Geometric Relationship between Lines and Planes
A 38-minute video from Yang Cao: “Tutorial on Geometric Relationship between Lines and Planes”.